- #Xentry das serial port how to
- #Xentry das serial port serial number
- #Xentry das serial port software
RS232 cable, from this time, the problem must be with one With so much time invested I decided to get another C3 Mux and
#Xentry das serial port software
Said it must be a software problem, to purchase a plug-in HDD from
When I restarted VMWare nothing worked again. The green comm light came on the deskband!!Įureka. Hours (arg!) the Chinese tech operated Teamviewer and evidently changed
So one night in the wee hours I setup the system and after several After much screwing around and getting nowhere Iįinally contacted the vendor through their website contact portal. So the problem must be in the Mux itself or a cabling issue beyond USB serial cable) won’t beĪvailable unless you disconnect VMWare’s use of it. Host (ie Win 10 in my case) the device (i.e. Its imperative that VMWare recognize that you want to disconnectįrom the host and put a check-mark by the device listing after theĭialog comes up asking permission. “Removable Device” (which can be a thumb drive if you want to importĭata, or the DVD drive, or USB cable) be selected from a “VM” menu dropĭown. My version of VMWare Workstation (10.0) requires a So I know either cable will work (if sometimes VMWare I connected each to the serial input of an old IBM w/ serial portĪnd used serial bus comm software to send/receive data from eachĬomputer. To be certain they were communicating through I started troubleshooting with the USB RS232 cable and tried one withįTDI and one without. Modules on the serial cable, and that engine diagnostic tool C3 Part D is unsupported post 09/2014. Setting COM Port 2, setting low serial bit rate, fake RS232-RS485 I had read all the caveats on the forums about RS232 cable type, However the SDConnect Toolkit showed the Mux as “Part D” but “noĬonnection”. Optimistically I connected it all up to the car (2004 W220.170, S430)īut did not get the green “Connected” icon in the desk band. Through the forums here to get the necessary keys for WIS/EPC/Xentry. VMWaredoes nicely run the XENTRY/DAS software on the virtual desktop I am using a Dell Inspiron 15 laptop with Windows 10. RS232 and OBD cables separately from other vendors as well.
#Xentry das serial port serial number
Apparently these Multiplexers are Actiaĭerivatives with the same serial number (6511100299), Part D4. I didn’t want to spend that much and shopped on-line acquiring anĮxternal USB HDD with 05-2015 software and VMWare loaded. Multiplexer, cables, Dell 630 (built-in RS232 port), already loaded There are many non-factory setups available with prices generally ~$600 for a C3 Star In your Windows MAIN folder and in your HHTWin.Like many others I had a long, long struggle getting my Mercedes Star Diagnostic XENTRY-DAS setup working and thought I would share some of the learning to the forum.
PLATFORM=PART_T (or optional _W for Wi-Fi ONLY communication)Ģ. In your F:ProgrammeDASbin folder in your Cal.ini file this: To switch from PartD MB Star c3 to SD connect C4, you making these few simply changes:ġ. You also can modify the cal.sli by youself. Replace the attached file (cal.sli) in F:programmeXentrybinllist and make it Read Only.] Then: Set local-connect nbsp IP to: 172.29.127.119/255.255.0.0īefore you try to running MB Starc Xentry with your SD connect C4 Multiplexer Connected, pls enjoy it.Ĭonvert MB Star C3 PartD (C3) To SD connect (C4) :ĭownload Convert_C3_to_C4 tool.rar, and just run it on your MB star c3 Diagnosis software.
#Xentry das serial port how to
If you have old MB star c3 Diagnosis, and want use new SD connect C4 Diagnosis, How to change Benz diagnosis DAS Setting, OBD2Motor share these steps.